The TMMS series consists of 5 different sizes of tri-section pulling plates suitable for shafts with maximum diameter ranging from 50 to 380 mm (2 to 15 in).

• The unique design of the TMMS series allows the application of force on most efficient point; the inner ring, and thereby requiring less force for dismounting than when pulling on the outer ring of the bearing housing
• The firm grip behind the bearing's inner ring ensures that the pulling forces are only transmitted through the inner ring and not through the outer ring or the rolling elements, preventing bearing damage
• The tri-section construction allows even force distribution, preventing bearing locking and/or tilting on the shaft, especially in the case of SRB and CARBŪ, during dismounting
• Suitable for use in combination with any three-armed puller
• Special wig shape allows the plates to be easily inserted between bearing and the shoulder on the shaft
• Available in a wide range, covering most common shaft sizes

Technical Data:

• TMMS 50
  • Width of Grip
    • d min: 12mm/ 0.5 in
    • d max: 50mm/ 2 in
    • M: n/a
  • A: 20mm/ 0.8 in
  • B: n/a
  • C: 32mm/ 1.3 in
  • Maximum withdrawal force(F max): 80 kN/ 8 ton imp.
  • Weight: 0.5 kg/ 1.1 lb
    
• TMMS 100
  • Width of Grip
    • d min: 26mm/ 1.0 in
    • d max: 100mm/ 3.9 in
    • M: M16 x2 mm
  • A: 36mm/ 1.4 in
  • B: 34mm/ 1.4 in
  • C: 60mm/ 2.4 in
  • Maximum withdrawal force(F max): 200 kN/ 20 ton imp.
  • Weight: 2.6 kg/ 5.7 lb
    
• TMMS 160
  • Width of Grip
    • d min: 50mm/ 2.0 in
    • d max: 160mm/ 6.3 in
    • M: M16 x2 mm
  • A: 45mm/ 1.8 in
  • B: 52mm/ 2.1 in
  • C: 82mm/ 3.3 in
  • Maximum withdrawal force(F max): 300 kN/ 30 ton imp.
  • Weight: 5.9 kg/ 13 lb
    
• TMMS 260
  • Width of Grip
    • d min: 90mm/  3.6in
    • d max: 260mm/  10.2in
    • M: M22 x2.5 mm
  • A: 70mm/ 2.8 in
  • B: 81mm/ 3.2 in
  • C: 110mm/ 4.3 in
  • Maximum withdrawal force(F max): 450 kN/ 45 ton imp.
  • Weight: 18.4 kg/ 41 lb
    
• TMMS 380
  • Width of Grip
    • d min: 140mm/ 5.5 in
    • d max: 380mm/ 15 in
    • M: M32 x2.5 mm
  • A: 81mm/ 3.2 in
  • B: 97mm/ 3.8 in
  • C: 138mm/ 5.4 in
  • Maximum withdrawal force(F max): 600 kN/ 60 ton imp.
  • Weight: 50.3 kg/ 110 lb

Puller selection
The table below shows which SKF pullers can be used in combination with the TMMS Puller selection

	TMMS 50	TMMS 100	TMMS 160	TMMS 260	TMMS 380
TMMP 3x185	x	o	-	-	-
TMMP 3x230	x	o	-	-	-
TMMP 3x300	o	x	o	-	-
TMMP 6	x	-	-	-	-
TMMP 10	-	x	-	-	-
TMMP 15	-	x	x	-	-
TMHP 8	x	x	o	-	-
TMMA 3	x	-	-	-	-
TMMA 5	x	o	-	-	-
TMMA 8	o	x	x	-	-
TMHP 15	-	-	o	o	-
TMHP 30	-	-	-	x	o
TMHP 50	-	-	o	x	x

                   x = recommended          o = possible          - = not possible