The Ultraprobe 9000KT
The Ultraprobe 9000KT Complete Kit is a digital ultrasonic
inspection, information storage and retrieval system that is so
versatile, so easy (most operators are able to use the Ultraprobe 9000
within 15 minutes) and so much fun to operate, you'll be looking for
opportunities to use it every day.
From the very instant you hold the Ultraprobe 9000 Ultrasonic
Inspection System in your hand, the feel of the well balanced pistol
grip, the elegance of simplicity and the clarity of signal will convince
you that this is truly a remarkable feat of engineering. This
Ultraprobe is ready to unleash the potential of any inspection program.
Complete Kits Include the following:
DHC-2 DELUXE NOISE ISOLATING HEADSET:
heavy duty headset is designed to block out intense sounds (over 23 dB
of noise attenuation) often found in industrial environments so that the
user may easily hear the sounds received by the ULTRAPROBE 9000.
WTG-1 WARBLE TONE GENERATOR:
Warble Tone Generator is used to provide a sensitivity validation
(Calibration) test. It is also used as an ultrasonic transmitter
designed to flood an area with ultrasound as part of a leak test. When
placed in an empty container, it will flood that area with an intense
ultrasound that will flow through a leak hole.
RFE-9 RUBBER FOCUSING PROBE:
Rubber Focusing Probe is a cone shaped rubber shield. It is used to
block out stray ultrasound and to assist in narrowing the field of
reception of the "Trisonic" Scanning Module.
USB DATA OUTPUT/INPUT CABLE
BCH-9 BATTERY CHARGER:
is the standard battery charger for the Ultraprobe 9000 with a line
input of 120 Volts AC @ 60 Hz. The charging time is about 8 hours. (For
countries with 220 Volts @ 50 Hz, the BCH-92 is considered a standard
BCH-WTG BATTERY CHARGER:
is the standard battery charger for all Warble Tone Generators that are
used with the Ultraprobe 9000. The line input is 120 Volts AC @ 60 Hz
and the charging time is about 8 hours. (For countries with 220 Volts @
60 Hz, the BCH-WTG2 is considered a standard accessory)
SCM-9 TRISONICTM SCANNING MODULE:
module receives air-borne ultrasounds such as those emitted by
pressure/vacuum leaks and electrical discharges. The Trisonic Scanning
Module has a phased array of three piezoelectric transducers which
focuses the ultrasound on one "hot spot" for directionality and
effectively intensifies the signal so that minute ultrasonic emissions
can be detected.
STM-9 STETHOSCOPE (CONTACT) MODULE:
module has a metal rod that acts as a "waveguide". It is sensitive to
ultrasound that is generated internally such as within a pipe, bearing
housing or steam trap. Once stimulated by ultrasound, it transfers the
signal to a piezoelectric transducer located directly in the module
housing. It is "module shielded" to provide protection from stray RF
waves that have a tendency to effect electronic receiving and
measurement. It is equipped with low noise amplification to allow for a
clear, intelligible signal.
SLP-EXT STETHOSCOPE EXTENSION KIT:
consists of three metal rods that will enable a user to reach up to 31
additional inches (78.7 cm) with the Stethoscope Probe.
Pistol Grip Housing is the main control unit. It consists of the
display panel, the "Spin & Click" controls for volume/frequency
adjustment, data entry and data storage, the headphone jack, battery,
I/O port, trigger on/off switch and module receptacle.
HALLIBURTON CARRYING CASE
The Ultraprobe 9000IS - Rated Intrinsically Safe
Now you can test in hazardous environments with the Ultraprobe
9000IS. Rated Intrinsically Safe, for use in Class I, Division 1, Groups
C & D by both Factory Mutual and CSA.
With this rating, users can assuredly enter environments such as
ethylene and propane without risking an explosion or fire (as long as
plant safety procedures are followed).
The Ultraprobe 9000IS is a digital instrument with on-board data
logging and frequency tuning features that enable inspectors to identify
sources of potential mechanical failure, electric faults and leakage in
With uploading and downloading capability, the Ultraprobe 9000IS
interfaces with UE Systems Ultratrend DMS data management software.
This powerful program records test data, organizes reports, produces
trend charts, sets alarm groups and links with UE Systems Compressed Gas
Software which reports leak surveys in terms of energy dollars saved
and carbon footprint impact.
The Ultraprobe 9000 ATEX - Rated Intrinsically Safe
The Ultraprobe 9000 ATEX lets you test in hazardous environments.
With the ATEX Rated EEx ib IIB Gb Ultraprobe 9000, users can assuredly
enter environments such as ethylene and propane without risking an
explosion or fire (as long as plant safety procedures are followed).
As with other Ultraprobe 9000 models, the digital Ultraprobe 9000
ATEX features on-board data logging and frequency tuning that help
inspectors identify sources of potential mechanical failure, electric
faults and leakage in plants.
Uploading and downloading capability via a USB connection interfaces
the Ultraprobe 9000 ATEX with UE Systems Ultratrend DMS data management
software. This powerful program records test data, organizes reports,
produces trend charts and sets alarm groups. Ultratrend DMS also links
with UE Systems Compressed Gas Software which reports leak survey cost
avoidance and details the reduction of carbon footprint gases related to
the leak repairs.