|
CMCP-261 Liquid Tight Strain Relief Connectors
|
|
ADASH VIBRIO III
|
|
Dual Parameter Loop-Powered Vibration and Temperature Transmitter
|
|
|
|
Please call for pricing
|
|
|
|
|
|
|
used for making direct accelerometer or transducer extension cable entries into the junction boxes listed - Temperature rated to -40 to 212 F (-60 to 100 C)
- Connectors have a pressure rating of up to 150 PSIG
- Need additional sizes? Please call 800-710-6786
|
- Powerful machine health checker
- Vibration measurements in acceleration, velocity and displacement
- FFT spectrum, time signal and wideband values measurements
- Expert system for determining of unbalance, misalignment, looseness and bearing fault
- Built-in stroboscope and non contact thermometer
- Bearing condition measurement, including slow-running ones
- Insufficiently lubricated bearings location
|
Dual Parameter Loop-Powered Vibration and Temperature Transmitter
|
|
|
|
CMCP-525A Vibration Acceleration Monitor - Ordering Page
|
|
CMCP-530A Vibration Velocity Monitor - Ordering Page
|
|
ADASH VA4Pro 4 channel Vibration Analyzer, Data collector, Balancer and Signal recorder
|
|
|
|
|
Call for pricing
|
|
|
|
|
|
|
The CMCP525A Acceleration Monitor is available in either "Peak" or "True RMS" signal detection versions. The CMCP525A is compatible with all voltage output accelerometers, and provides a 4-20 mA output proportional to the overall measurement. Each unit provides constant current power for the accelerometer, checks for faults, processes the vibration signal to determine overall amplitude, and outputs a 4-20 mA dc current that is proportional to a user selected range of 5, 10, 15, 20 or 25 g's with a 100 mv/g Input.
|
The CMCP530 Accelerometer based Velocity Monitor is available in either "Peak" or "True RMS" signal detection versions and English or Metric scaling. The CMCP530 is compatible with all voltage output accelerometers, and provides a 4-20 mA output proportional to the overall measurement. Each unit provides constant current power for the accelerometer, checks for faults, processes the vibration signal to determine overall amplitude, and outputs a 4-20 mA dc current that is proportional to a user selectable range of 0.5, 1.0, 1.5, 2.0 and 2.5 in/sec (metric equivelant of 12.7, 25.4, 38.1, 50.8 and 63.5 mm/sec) with a 100 mv/g Input. Combining transmitters with an existing PLC or DCS system results in a high density, low cost vibration monitoring system.
|
Adash VA4Pro data collector and signal analyzer is determined for all tasks of vibration diagnostics. It enables analysis of bearing condition, mechanical defects (unbalance, misalignment, resonance, looseness), lubrication.
|
|
|
|
BNC-Male To BNC-Male Shielded Cable 3ft up to 100ft
|
|
CMCP-805 Eddy Probe Bracket 3/8"-24
|
|
CMCP-805 Eddy Probe Bracket 1/4"-28
|
|
|
|
Our Price: $35.00
|
|
|
|
Our Price: $35.00
|
|
|
|
|
|
|
BNC-Male To BNC-Male Shielded Cable 3ft up to 100ft
|
Mounting Brackets are used when installing eddy probes (proximity probes) internally in the machine - For 3/8"-24 threaded probes
- Machined aluminum
- Threaded and slotted to insure position and stability
|
Mounting Brackets are used when installing eddy probes (proximity probes) internally in the machine - For 1/4"-28 threaded probes
- Machined aluminum
- Threaded and slotted to insure position and stability
|
|
|
