|
The SKF medium induction heater TIH 100m has the same high standards of efficiency and performance as the smaller heater TIH 030m, combined with increased capacity. The advanced design of the power electronics allows features of accurate electric current control, cut-outs to avoid overheating, controls on rate of temperature increase, these are as some of the standard features in the TIH...m range.
Placing the induction coil outside the heater’s housing allows the heating of bearings weighing up to 120 kg (264 lb). The heater is equipped with thermal overheating protection to reduce the risk of damage to the induction coil and the electronics. In addition to temperature mode, the TIH 100m is equipped with a time mode for heating components other than bearings. The heater is supplied standard with three yokes and is available in two executions:
-
230V/50-60Hz or
-
400-460V/50-60Hz.
View Product Video
|
Additional Info:
 |
Induction coil outside the heater’s housing allows shorter heating time and lower energy consumption |
 |
Foldable bearing support arms facilitate the heating of larger diameter bearings |
 |
Magnetic temperature probe helps prevent bearing overheating |
 |
Easy–to–use control panel and LED display integrated in a remote control |
 |
Internal storage for all 3 yokes reduces the risk of yoke damage or loss |
 |
Integrated carrying handle facilitates portability |
 |
Swivel arm |
-
Standard swivel arm for large size yoke
-
Capable of heating a 97 kg (213 lb) bearing in less than 20 minutes, saving time and energy
-
2-step power setting and smaller yokes allow heating smaller bearings safely and at lower power consumption
-
Temperature mode pre–set at 110 °C (230 °F) to help prevent bearing over–heating
Automatic demagnetisation 3 years warranty SKF m20 concept "m20" represents the weight (kg) of the heaviest SRB 231 bearing which can be heated from 20 to 110 °C (68 to 230 °F) in 20 minutes. This defines the heater’s power output instead of its power consumption.
Technical data
-
SKF m20 performance: 97 kg (213 lb)
-
Voltage, V/Hz:
-
230V/50-60Hz or
-
400-460V/50-60Hz
-
Work piece:
-
Maximum weight: 120 kg (264 lb)
-
Maximum bore diameter: 20 - 400 mm (0,8 - 15,7 in)
-
Temperature control:
-
Range: 0 - 250 °C (32 - 482 °F)
-
Magnetic probe: Yes, K-type
-
Accuracy (electronics): ± 2 °C (± 3.6 °F)
-
Time control:
-
Range: 0 - 60 minutes
-
Accuracy: ± 0.01 sec.
-
Maximum temperature (approx.): 400 °C (750 °F)
-
Thermometer mode: Yes
-
Bearing mode: Yes
-
Power reduction: 2-step; 50 - 100%
-
Demagnetisation according to SKF norms (automatic): Yes (<2 A/cm)
-
Can heat sealed bearings: Yes
-
Can heat pre - greased bearings: Yes
-
Error guiding codes: Yes
-
Thermal overload protection: Yes
-
Maximum magnetic flux: 1,7 T
-
Control panel: Key board with LED in remote control
-
Operating area (w × h): 155 × 205 mm (6,1 × 8,0 in)
-
Coil diameter: 110 mm (4,3 in)
-
Dimensions (w × d × h): 570 × 230 × 350 mm (22.4 × 9.0 × 13.7 in)
-
Total weight, including yokes 42 kg (92 lb)
-
Maximum power consumption:
-
3.6 kVA (230V)
-
4.0-4.6 kVA (400-460V)
-
Number of standard: yokes 3
-
Standard yokes:
-
56 × 56 × 296 mm (2,2 × 2,2 × 11,7 in), for heating bearings with bore diameter of 80 mm (3.1 in) and larger
-
28 × 28 × 296 mm (1,1 × 1,1 × 11,7 in), for heating bearings with bore diameter of 40 mm (1.6 in) and larger
-
14 × 14 × 296 mm (0,6 × 0,6 × 11,7 in), for heating bearings with bore diameter of 20 mm (0.8 in) and larger
-
Core cross section: 56 × 56 mm (2,2 × 2,2 in)
-
Yoke storage: Yes, foldable
-
Sliding arm No Swivel arm: Yes, large yoke only
-
Cooling fan: No
-
Housing material: Steel and glass filled polyamide
-
Warranty period - 3 years
|
|
