Submit search
CMCP240 Proximity Switch
CMCP420VT-EX-01, IECEx/ATEX Approved Loop-Powered Vibration Velocity Transmitter with Dynamic Output, 0-1 in/sec. (0-25.4 mm/sec.)
CMCP420VT-Ex-02, IECEx/ATEX Approved Loop-Powered Vibration Velocity Transmitter with Dynamic Output, 0-2 in/sec (0-50.8 mm/sec).
CMCP420VT-T/Ex-01, IECEx/ATEX Approved 4-20mA Dual Output Vibration and Temperature Output. 0-1 in/sec (0-25.4 mm/sec).
CMCP420VT-T/Ex-02, IECEx/ATEX Approved 4-20mA Dual Output Vibration and Temperature Output. 0-2 in/sec (0-50.8 mm/sec).
The CMCP601R Reciprocating Compressor Demonstration Kit is designed to demonstrate vibration monitoring techniques used on Reciprocating Machinery. Fully equipped with sensors the CMCP601R can be equipped with Accelerometers on the Motor/Gear, Crosshead and Cylinder End along with Proximity Probes in the Crosshead for Rod Drop and Rod Runout. A mounting bracket and machined Flywheel Notch are provided for a Proximity Probe Keyphasor or other type of once per turn reference signal. Two shaft connecting rod holes are provided for adjusting the total stroke distance.FEATURES:Mini Reciprocating Compressor Kit Battery Powered (Lithium-Ion) 0-300 RPM Adjustable Height Cylinder Rod Drop and Rod Runout Crosshead Vibration Crosshead Pin Reversal Motor/Gear Vibration Cylinder End Vibration 15+ Hours Battery Life Custom Carrying CaseThe Battery Powered DC Motor has an adjustable speed of 0 to 319 RPM (0 to 5.3 Hz). The Cylinder is independently mounted on two vertical spring-loaded linear bearings and height (alignment) can easily be adjusted to demonstrate both Rod Drop and Rod Run Out. The Crosshead has both upper and lower Oil Infused Bronze Bearings (Slippers) and the Piston rides on actual Wear Ring Stock. The Connecting Rod has Bronze Bearings on both ends and connects the Flywheel (Crank) to the Crosshead Pin. Stroke can be adjusted on the Flywheel between 1” and 1.25” (25.4, 31.75 mm).The Battery Powered DC Motor has an adjustable speed of 0 to 319 RPM (0 to 5.3 Hz). The Cylinder is independently mounted on two vertical spring-loaded linear bearings and height (alignment) can easily be adjusted to demonstrate both Rod Drop and Rod Run Out. The Crosshead has both upper and lower Oil Infused Bronze Bearings (Slippers) and the Piston rides on actual Wear Ring Stock. The Connecting Rod has Bronze Bearings on both ends and connects the Flywheel (Crank) to the Crosshead Pin. Stroke can be adjusted on the Flywheel between 1” and 1.25” (25.4, 31.75 mm).The CMCP601R Reciprocating Compressor Demonstration Kit comes complete with: Reciprocating Compressor, Carrying Case, Speed Controller, Rechargeable Li-Ion Battery and Charger. Sensors are Optional and are provided on request along with 9” Sensor Plate. Reciprocating Compressor Dimensions: 13” L x 4” W x 5.1” H (330 x 102 x 130mm)
Sensor Interface for up to Eight (8) Channels of Accelerometers and Proximity Probe Systems. Provided with two (2) CMCP300P Interfaces and DIN Rail on a Mounting Plate. Rubber feet are provided. Shipped with one (1) additional Battery Pack that along with the Battery Pack provided with the CMCP601R will provided both + and - 24 VDC.Dimensions: 9" L x 5" W x 3.7" H (228.6 x 127 x 94.2mm)
The Sensor Kit for the CMCP601R Reciprocating Compressor Demonstrator includes three (3) CMCP1100-05 100 mv/g Accelerometers for Motor/Gear, Crosshead and Cylinder End. Two (2) 5mm by 1 meter length Proximity Probe Systems are provided for Keyphasor and Rod Drop/Runout measurement.
CMCP788A Premium Accelerometer, Top Exit
CMCP801QD-01 Quick Disconnect Proximity Probe Holder for 3/8-24" Proximity Probe
CMCP801QD-02 Quick Disconnect Proximity Probe Holder for 1/4-28" Proximity Probe
Back to top
